7-65 through hole lamps package dimensions t-1 3 / 4 (5mm) medium profile led lamps LTL-10203 red ltl-10213 bright red ltl-10223 high efficiency red ltl-10233 green ltl-10253 yellow features low power consumption. wide viewing angle. medium profile: 7.24mm (0.285 ) nominal. general purpose leads. i.c. compatible/low current requirement. reliable and rugged. description the red source color devices are made with gallium arsenide phosphide on gallium aresnide red light emit- ting diode. the bright red source color devices are made with gallium phosphide on gallium phosphide red light emit- ting diode. the high efficiency red and orange source color de- vices are made with gallium arsenide phosphide on gallium phosphide orange light emitting diode. the green source color devices are made with gallium phosphide on gallium phosphide greenlight emitting diode. the yellow source color devices are made with gallium arsenide phosphide on gallium phosphide yellow light emitting diode. notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted. 3. protruded resin under flange is 1.5mm (.059") max. 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without notice. ltl-102x3 series part no. ltl- lens source color red bright red hi. eff. red green yellow 10203 10213 10223 10233 10253 red diffused red diffused red diffused green diffused yellow diffused devices 4 .com u datasheet
7-66 lead soldering temperature [1.6mm (.063 in.) from body] 260 for 5 seconds absolute maximum ratings at ta=25 parameter power dissipation 80 200 40 0.5 5 -55 to +100 -55 to +100 continuous forward current derating linear from 50 reverse voltage operating temperature range storage temperature range peak forward current (1/10 duty cycle, 0.1ms pulse width) red bright red green yellow hi. eff. red unit 40 60 15 0.2 5 100 120 30 0.4 5 60 80 20 0.25 5 100 120 30 0.4 5 mw ma ma ma/ v 4 .com u datasheet
7-67 through hole lamps typ. 0.4 1.7 3.7 3.7 3.7 min. 1.1 5.6 12.6 12.6 12.6 60 655 697 635 565 585 max. 2.0 2.6 2.6 2.6 2.6 100 unit. mcd deg nm nm nm v a pf test condition. note 2 (fig.7) i f =10 ma note 1,4 measurement @peak (fig.1) v r =5v i f =20ma v f =0 , f=1mhz electrical/optical characteristics at ta=25 parameter symbol part no. ltl- luminous lntensity viewing angle peak emission wavelength spectral line half width forward voltage reverse current capacitance i v 2 p v f i r c 10203 10213 10223 10233 10253 notes:1.luminous intensity is measured with a light sensor and filter combination that approximates the cie eye- response curve. 2. is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3.the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4.i v needs 15% additionary for guaranteed limits. 102x3 10203 10213 10223 10233 10253 10203 10213 10223 10233 10253 10203 10213 10223 10233 10253 102x3 10203 10213 10223 10233 10253 note 3 dominant wavelength d 10203 10213 10223 10233 10253 651 657 623 569 588 24 90 40 30 35 1.7 2.1 2.0 2.1 2.1 30 55 20 35 15 4 .com u datasheet
7-68 typical electrical/optical characteristic curves (25 ambient temperature unless otherwise noted) 4 .com u datasheet
|
